Grips, Clamps + Studs

The 4.5 ” Grip head fits into a 1-1/8″ ( 28mm ) receiver.  It also has a 1-1/8″...

The 2.5″ grip head fits on 5/8″ ( 16mm ) Baby Pin mount. The MSE 2.5 ” Grip Head...

5/8″ Baby Pin Receiver and ratchet handle, securely grip to any stand or pipe and support fixtures...

9″ A-Clamp aka Pony Clamp, Spring Clamp or grip clip is the industry standard for clamping backdrops,...

6″ A-Clamp aka Pony Clamp, Spring Clamp or grip clip is the industry standard for clamping backdrops,...

This clamp provides strong sturdy gripping of Various types of pipe including angle, round, square...

This Matthellini clamp provides strong sturdy gripping of Various types of pipe including angle, round,...

The largest of the Cardellini clamps the 6″ End jaw also provides strong sturdy gripping of...

MSE Extendellini Clamp Adapter increases the gripping range of any Center Jaw Matthellini Clamp by...

A solid pipe clamp with a 1-1/8″ (28mm)  pin attached.
The MSE Big Ben clamp –...

Swivel Pipe Clamp for 1-1/4″ or 1-1/2″ O.D pipe diameter. rotates at full 360 degrees...

Fixed 90 degree dual pipe clamp. Made for building frames or anywhere you need pipe at a 90 degree...

Pipe clamp with a 1-1/8″ ( 28mm ) receiver. Attached is safety chain with cotter pin. Easily...

Used to mount onto pipe, and has a 5/8″ ( 16mm ) baby pin allowing you to mount light fixtures...

MSE Chain Vice Grip has two 5/8″ ( 16 mm ) baby pin mounts, one on the end that doubles as an...

Ideal for positioning / clamping foamcore or bead board ( aka Styrofoam ). It has a 5/8″ ( 16mm...

Clench jaw with rubber grip pads for a secure grip while preventing damage on soft surfaces. the MSE...

MSE 1-1/8″ ( 28mm ) to 5/8″ ( 16mm ) adapter is the industry standard for converting Junior...

The E 600 has a hexagonal end that snaps into a Super Clamp ( aka Maffer Clamp ) or grip head to provide...

The Strobepro Baby pin is a 5″ baby pin. It has 3 tightening notch.

Specs:

• Length:...

Attaches to a Super Clamp aka Mafer Clamp socket via 5/8″ ( 16mm ) stud and can be used for...

This adapter spigot can snap into Super Clamps (aka Mafer Clamp) with a 5/8″ hexagonal end and...

Universal 16 mm spigot with double male thread with 1/4” and 3/8”.

MSE Drop Ceiling Scissor Clamp. Mounts on suspended ceiling track and has a 5/8″ ( 16mm ) Baby...

1/8″ x 32″ Wire Safety cable with carabiner used to ensure safety with hanging fixtures.

Specs:

• Total...

Designed for use of large lights like Sufa 400’s or Sufa 800’s. The MSE Triple header...

A steel plate with a 1 1/8″ ( 28mm ) receiver. It has holes drilled in each corner for screwing...

Designed to be used with Telescoping Hangers. a 1-1/8″ ( 28mm ) receiver ( aka Junior Receiver...

A steel 3″ plate with a 5/8″ ( 16mm ) Baby Pin welded to it and holes drilled in each...

This Baby Nail-On is a steel 6″ plate with a 5/8″ ( 16mm ) Baby Pin welded to it and holes...

This base Plate is 5.5″ in diameter and has a 5/8″ ( 16mm ) mount. It has 4 non threaded...

Easily slide in Baby Plates ( aka 750 Pigeons ) to the spring loaded slots with no hardware required....

Large Stand side arm extension. It Clamps to center of stand and provides a lower mount point for...

Can be used with the Shiny Board (standard Reflector) to mount 2 heads to shine light into shiny board....

The Manfrotto Camera bracket has two 5/8″ ( 16mm ) receivers. It also has a  1/4″ –...

Double Extension – 3ft – 6ft

This MSE  single column is designed to fit in C-Stand turtle base legs and Runway base with its 1-1/8″...

Works with 1″ (2.5cm) O.D  Square Frames. Allows you to place Backdrops flat with walls or...

Works with 2″ (5cm) O.D Pipe and allows you to set your backdrops flat to the wall. Slide the...

Manfrotto Magic arm. Knob easily tightens and loosens. It has two articulating 5/8″ ( 16mm )...

3 Articulating ball joint arms with a 5/8″( 16mm ) snap-in baby pin mount on one side intended...

Made for clamping onto support beams, I-Beams, crossbars or hard to attach to shapes. It has two separate...

This 10″ C  Clamp is made for clamping onto support beams, I-Beams, crossbars or hard to attach...

Made for...

This pivoting Boom clamp has a 1-1/8″ ( 28mm ) male mount with indexed ratchet handle, and 5/8″...

Used to mount umbrellas and has two 5/8″ ( 16mm ) receivers on each end with a pivoting ratchet...